PA, PPS, PBT selected hBN for heat conduction compound

Problem

Selecting hBN requires a system-level thermal decision. Filler conductivity alone does not predict compound viscosity, particle packing, bond-line thickness, contact resistance, electrical insulation, or reliability.

Mechanism

Heat moves through particle contacts and interfaces in the cured or solid composite. Particle size, morphology, orientation, loading, wetting, voids, pressure, and thickness determine whether the filler forms a useful thermal path.

Tradeoff

Increasing hBN loading can improve thermal transport while increasing viscosity, torque, brittleness, sedimentation risk, dispensing force, or interfacial defects. The best formulation meets the system thermal-resistance target inside the available processing window.

Material Strategy

Use the following decision sequence to define the host system, compare candidate materials, establish a process window, and confirm the final part. The guidance is method-conditioned and does not replace grade-specific data or application testing.

key answers

For a practical review of hBN for thermally conductive PA·PPS·PBT, comparing only product names or supplier representative figures is not sufficient. First, the required functions of the final part or film, acceptable appearance and processing range, and actual test conditions must be defined. Then, candidate materials must be compared under the same base material, thickness, process, and conditioning conditions to obtain meaningful conclusions.

This page does not claim that any particular grade is superior to all systems. The function of the material depends on the resin or binder, particle dispersion, addition amount, shape, process and measurement method. Before purchasing, you must check what composition, test specimen, and method the values ​​in the technical data were obtained from, and conduct an evaluation that reflects actual mass production conditions.

Processing temperature and viscosity for each resin

‘Processing temperature and viscosity for each resin’ is a condition that must be checked before the name of the additive. The wetting and distribution of the same functional particle varies depending on the polarity, viscosity, moisture, plasticizer, flame retardant, pigment, and hardener of the resin. Low compatibility may result in agglomeration, layer separation, appearance defects, or functional deviations.

Candidate materials are compared to actual production resins and additive packages. Do not apply the results of alternative resins or simple model binders as is, but re-verify them under actual process conditions, including mixing order and heat history.

Fiber·hBN Hybrid

The ‘Fiber·hBN Hybrid’ item should be treated as an independent decision-making criterion for hBN for thermally conductive PA·PPS·PBT. First, target values, measurement methods, allowable deviations, and failure criteria are documented and then candidate materials are compared. If conditions are not fixed, it is difficult to distinguish between material differences and test deviations.

Evaluation results include not only average values but also repeated measurements and ranges. When the goal is not met, the cause is identified by separating additives, base material, dispersion, process, specimen shape, and measurement conditions in that order.

flow direction

The ‘flow direction’ item should be treated as an independent decision-making criterion for hBN for thermally conductive PA·PPS·PBT. First, target values, measurement methods, allowable deviations, and failure criteria are documented and then candidate materials are compared. If conditions are not fixed, it is difficult to distinguish between material differences and test deviations.

Evaluation results include not only average values but also repeated measurements and ranges. When the goal is not met, the cause is identified by separating additives, base material, dispersion, process, specimen shape, and measurement conditions in that order.

Strength, torsion, insulation

The ‘strength, torsion, and insulation’ items should be treated as independent decision-making criteria for hBN for thermally conductive PA·PPS·PBT. First, target values, measurement methods, allowable deviations, and failure criteria are documented and then candidate materials are compared. If conditions are not fixed, it is difficult to distinguish between material differences and test deviations.

Evaluation results include not only average values but also repeated measurements and ranges. When the goal is not met, the cause is identified by separating additives, base material, dispersion, process, specimen shape, and measurement conditions in that order.

Heat conduction evaluation by injection product direction

In the ‘Heat conduction evaluation by injection product direction’ section, it is dangerous to pass a material with only a single resistance value. The conductive network is affected not only by the amount added, but also by filler distribution, flow direction, specimen thickness, measurement location, humidity and thermal history. Especially in the sections before and after percolation, small process deviations can lead to large resistance deviations.

First determine whether surface resistance, volume resistance, or ground resistance describes the actual risk of use. It can be used as a supply specification only when repeated measurements are made under the same conditioning and electrode conditions, and the molding location, direction, and distribution by lot are recorded.

Recommended Evaluation Procedure

1. Target functions and failure conditions are defined by numerical or observation criteria.
2. A standard specimen is created using the base material, additive package, and substrate that will be used in mass production.
3. Rather than changing all variables at once, compare material types, addition amounts and key process conditions step by step.
4. In addition to initial functionality, appearance, processability, mechanical or adhesive properties and required durability are measured.
5. The optimal conditions are repeated on different raw material lots, on different dates, and in actual production facilities to confirm the process window.

The test report includes the name of raw materials, lot, mixing, specimen thickness and shape, equipment, temperature, time, speed, conditioning, and measurement method. Without this information, it is difficult to fairly compare results between suppliers or between lab and mass production.

Information to provide to suppliers

• Exact type and grade of base resin, binder or substrate
• Target function value, measurement method and tolerance range
• Limitations on color, transparency, surface, viscosity or mechanical properties
• Mixing, extrusion, injection, application, drying or curing conditions
• Thickness, shape and usage environment of specimens and final parts
• Required TDS, SDS, regulatory documentation and change management level
• Evaluation sample quantity, development schedule and expected mass production scale

Frequently Asked Questions

Can I select a grade based solely on representative values from the datasheet?

Representative values are useful for narrowing down candidates, but are insufficient as a basis for final selection. If the test composition, method, thickness and conditions are different from the actual system, the same results cannot be expected.

Is the highest dosage safest?

Not really. Higher additions may increase functionality but may worsen viscosity, torque, brittleness, color, haze, surface or cost. We need to find the minimum range that reliably satisfies the goal.

Can laboratory results be directly applied to series production?

Equipment size, shear, residence time, heat history and part geometry will vary and should not be applied without confirmation. It must be re-verified step by step in pilot and mass production facilities.

Request evaluation samples and technical reviews

Please send us your resin grade, part geometry, thermal direction, and mechanical property goals. Please include the above input information with your request. The more specific the information, the faster you can narrow down the appropriate supply form - powder, masterbatch, or dispersion - and reduce unnecessary repetitive testing.

Recommended Architectures

• Use a matched baseline with the intended host resin, binder, substrate, color package, thickness, and geometry.
• Screen supplied form, loading, dispersion, and process variables in a bounded matrix.
• Advance only candidates that meet functional, processing, appearance, mechanical, and durability requirements together.
• Repeat the accepted window on production-relevant equipment and multiple raw-material lots.

Related Products

• hBN

Related Applications

• Thermally Conductive Electrically Insulating Polymers

Downloads & Engineering Support

Review the related Dispersion Engineering Overview Video, then request an application-specific technical review.